:
Monitor four measurement points with the Sato SK-L400T 4-channel temperature data logger. Connect Type K thermocouple probes, view all four readings together and record temperature data to an SD card.
Compare temperatures at four locations without switching between separate meters. The Sato SK-L400T combines a four-channel temperature display with SD card recording, helping operators follow temperature changes and review the results after a measurement session.
Select Type K thermocouple probes to match each measurement point. For example, a test may require immersion probes for liquids, contact probes for surfaces or air probes around equipment. Check the probe's temperature rating, dimensions and cable length before ordering.
| Model / catalogue number | SK-L400T / 8191-00 |
|---|---|
| Inputs | 4 Type K thermocouple channels with miniature thermocouple connectors |
| Display range | -202.0 to 1372°C; usable measurement range depends on the connected probe |
| Main-unit accuracy | ±(0.3% of reading + 1)°C at 23 ±5°C; probe accuracy must also be considered |
| Surface-probe accuracy allowance | An additional 2% of reading applies when using a surface probe |
| Resolution | 0.1°C from -202.0 to 999.9°C; 1°C above this range |
| Sampling | Approximately every second |
| Logging intervals | 1, 2, 5, 10, 15 or 30 seconds; 1, 2, 5, 10, 15, 30, 60 or 90 minutes |
| Power | Four AA alkaline or NiMH rechargeable batteries; optional dedicated AC adapter |
| Typical battery life | Approximately 500 hours with alkaline batteries at room temperature, one-minute logging and the backlight and display switched off |
| Dimensions | Approximately 158 × 106 × 40 mm (W × H × D) |
| Weight | Approximately 420 g including batteries |
The dedicated 4ch Datalogger for Windows software supports graph plotting, channel statistics and accumulated-temperature analysis. CSV export allows further work in spreadsheet software.
Confirm software compatibility with your intended computer before purchase.
Probes are sold separately. The options below retain the illustrations from this product page. Confirm the required model and current availability when requesting a quotation.
| Probe model | Type | Illustration |
|---|---|---|
| SK-K010 | Standard immersion |  |
| SK-K020 | Quick response |  |
| MC-K7100 | Standard immersion |  |
| MC-K7101 | General purpose |  |
| MC-K7102 | High temperature |  |
| MC-K7103 | Asphalt; stainless steel grip |  |
| MC-K7105 | Shielded duplex wire |  |
| MC-K7106 | Asphalt; resin grip |  |
| MC-K7108 | Compost |  |
| MC-K7109 | Asphalt |  |
| MC-K7301 | Surface contact |  |
| MC-K7304 | Screw-mounted surface |  |
| MC-K7307 | Surface contact |  |
| MC-K7308 | L-shaped surface |  |
| MC-K7500 | Water temperature |  |
| MC-K7501 | Clip; black |  |
| MC-K7502 | Clip; red |  |
| MC-K7503 | Telescopic |  |
| MC-K7504 | Waterproof probe |  |
| MC-K7505 | Air; cable-connected |  |
| MC-K7506 | Air; plug-in |  |
Specify the required cable arrangement and length when ordering. Connector compatibility alone does not establish the suitability of a probe for your application.
Identify what each channel will measure before selecting accessories. Include the lowest and highest expected temperatures, required insertion depth or surface-contact arrangement, cable routing and recording duration.
Contact us for pricing and availability. Send the number of probes required, preferred probe models, quantity and any calibration requirements.
|
Download |
Monitor four measurement points with the Sato SK-L400T 4-channel temperature data logger. Connect Type K thermocouple probes, view all four readings together and record temperature data to an SD card.
The Anritsu AM-9000 series temperature datalogger records measurements across 6 or 12 channels, with fixed thermocouple and multi-input models available. Store readings in internal memory and transfer them to a PC through USB using optional AMS-950 analysis software.
AMS-950 software is sold separately.
Monnit ALTA® Wireless Thermocouple Sensors leverage Monnit’s award-winning remote monitoring platform to remotely monitor high-temperature applications, such as commercial ovens, kilns, and chimneys. Users benefit from a wireless data transmission range of 1,200+ ft, bank-grade security, and a temperature range of up to 400°C (752°F).
Monnit’s thermocouple is user-programmed to sleep for a specified interval, awake, capture analog data, and then convert this measurement into a temperature. If the sensor captures temperatures outside of user-specified thresholds, an alert is sent via text, email, or call. Monnit’s hardwired thermocouples feature a needle-style probe at the end of a 6’ lead (a K-Type Quick Connect Thermocouple is also available).
The Sekonic ST-50A digital thermohygrograph combines an electronic temperature and humidity display with continuous paper chart recording. View current conditions and retain a physical record for environmental checks.
Discontinued model: Manufacturer sales have ended. Remaining stock, consumables and alternative instruments are subject to availability.
Monnit ALTA Soil Moisture Sensor measures soil moisture tension & soil temperature within the soil. It uses a resistive granular matrix element to accurately measure the matric water potential (soil moisture tension) in the soil and a thermistor based temperature element to measure temperature.
- Safe to use in both hot & freezing temperatures
- Reports matric potential (soil water tension)
- Moisture readings in centibar & kPa
- 0 to 240 centibar (kPA)
- Will not dissolve in soil
- Internally compensated for commonly found salinity levels
- Easy to install and use compared to traditional tensiometers
- Stainless steel electrodes
- No maintenance required
- Temperature readings in C/F.
- 5 ft removable lead
Palmer Wahl pressure and temperature chart recorders provide a paper record of measurements over time. Choose an 8-inch or 12-inch recorder with an aluminium or Pelican® case, configured for pressure, temperature or combined recording.
The Sato SK-RHC-I temperature and humidity transmitter combines a local display with 4–20 mA outputs for connection to compatible monitoring and control equipment. Three interchangeable probe designs support different sensor positions.
Probe sold separately. An optional AC adapter is available.
Sekonic Universal 6 channel Recorder SP-100 / SP100 records from different sources simultaneously, including mA, V, PT100, Thermocouple.
Dickson OCEAView™ brings wireless environmental monitoring, alarm notifications and traceable records into one platform. Monitor temperature, humidity and other critical parameters using compatible data loggers and sensors for refrigerators, freezers, laboratories, pharmaceutical storage and cold rooms.
The Evikon E2244 humidity and temperature transmitter measures relative humidity and air temperature for connection to controllers, monitoring instruments and building management systems.
Dickson circular chart recorders provide a paper record of temperature, humidity, pressure or external transmitter signals, depending on the model. Select the recorder by measurement type, chart size, recording period and installation requirements.
Monnit ALTA Wireless Humidity (RH) Sensor allows you to accurately monitor the relative humidity of the air within a room or enclosure. - Measures relative humidity, temp
The Anritsu AM-8000 series temperature datalogger is a portable instrument available in 6- and 12-channel models for recording multiple measurement points. Internal memory stores readings for transfer to a PC using dedicated software.
Discontinued model: The AM-8000 series has been replaced by the Anritsu AM-9000 series.
The Isuzu TH27R (TH-27R) thermohygrograph is discontinued. For a replacement temperature and humidity chart recorder, choose the Sato NSII-Q (Sigma II).
The Sekonic ST-50M thermohygrograph records temperature and relative humidity on paper charts and an SD memory card. Its digital display provides local readings, while recorded electronic data can be reviewed on a computer.
Discontinued: The ST-50M is no longer available as a new instrument. This page provides reference information, consumable part numbers and alternative recording options.
The Sato SK-L200THIIα temperature and humidity datalogger is discontinued and has been replaced by the Sato SK-L750 series. For recording both temperature and relative humidity, select the SK-L754 with a suitable probe.
The Dickson TWP touchscreen data logger displays readings and measurement history on an 8-inch colour screen. Configure it for temperature, humidity or differential pressure monitoring using compatible replaceable sensors.
