RCM Direct Reading Differential Pressure Flowmeter for Liquid & Gas
There are 12 products.
Evikon Differential Pressure Transmitter E2618-DF is a member of new PluraSens® family of multifunctional measurement instruments. The transmitter is intended for measurement of low pressure of air and non-aggressive gases in HVAC applications.
Evikon Gas Transmitter E2618 series is intended for measurement of gases with high accuracy
Features:
- Industrial enclosure with IP65 protection
- Attached or remote sensor options
- Two analog outputs settable to 4-20 mA or 0-10 V
- RS485 Modbus RTU digital interface
- Power supply 12...36 VDC (default), 24 VAC as option
Evikon Humidity and Temperature Transmitter E2244 is is intended for measurement of relative humidity and ambient temperature in air and non-aggressive gases with high accuracy and stability.
Evikon Humidity and temperature transmitter E2218-DM is a member of new PluraSens® family of multifunctional measurement instruments. The transmitter is intended for measurement of relative and absolute humidity, temperature and dew point value in air with high accuracy and stability in non-aggressive gases.
Evikon E2218-DM features two freely configurable analog outputs 4-20 mA / 0-10 V and RS485 Modbus RTU interface for direct Fieldbus networking. The sensors are located at the tip of 200 mm long stem, intended for insertion into ventilation airducts.
RCM general purpose Flo-Gard II flow switches (liquid) reed switches make or break contacts by detecting the position of a magnet permanently attached to the bellow.
Our reed switches can also be ordered for use in hazardous location (Option IS), when fitted with
LED's (Option LED) it provides viewing at a glance when flow rate goes below or above the set point and makes field calibration easy.
Monnit ALTA Wireless Carbon Dioxide Sensor uses an ultra low-power, high-performance CO2 sensor to measure the amount of carbon dioxide in ambient air.
- Measures 0 to 10000 ppm CO2
- Accurate to +/- 45 ppm + 3% of reading
- Sensor produces instantaneous CO2 readings and 8 hour time weighted average(TWA) readings
Monnit ALTA Wireless Differential Pressure Sensor measures the pressure difference between two input ports and transmits the measurement to iMonnit.
- Measurement range: -500 Pa to 500 Pa
- Calibrated and temperature compensated
Monnit ALTA Wireless Humidity (RH) Sensor allows you to accurately monitor the relative humidity of the air within a room or enclosure. - Measures relative humidity, temp
Monnit ALTA Wireless PSIG Pressure Meter measures pressure in a gas, liquid or vapor supply line and transmits the pressure measurement to iMonnit. This solution combines a standard pressure transducer interfaced to a Monnit ALTA wireless radio.
- Measure pressure with 50 or 300 PSIG transducers (others available upon request)
- Measure non-caustic liquid or vapor pressures
- Pressure transducer is NEMA 4X (IP66), CE Rated
Monnit ALTA Soil Moisture Sensor measures soil moisture tension and soil temperature within the soil. It uses a resistive granular matrix element to accurately measure the matric water potential (soil moisture tension) in the soil and a thermistor based temperature element to measure temperature.
- Safe to use in both hot and freezing temperatures
- Reports matric potential (soil water tension) which is the best indicator of water availability in the soil.
- Moisture readings in centibar and kPa
- 0 to 240 centibar (kPA)
- Will not dissolve in soil
- Internally compensated for commonly found salinity levels
- Easy to install and use compared to traditional tensiometers
- Stainless steel electrodes
- No maintenance required
- Temperature readings in C/F.
- 5 ft removable lead
Monnit ALTA® Wireless Thermocouple Sensors leverage Monnit’s award-winning remote monitoring platform to remotely monitor high-temperature applications, such as commercial ovens, kilns, and chimneys. Users benefit from a wireless data transmission range of 1,200+ ft, bank-grade security, and a temperature range of up to 400°C (752°F).
Monnit’s thermocouple is user-programmed to sleep for a specified interval, awake, capture analog data, and then convert this measurement into a temperature. If the sensor captures temperatures outside of user-specified thresholds, an alert is sent via text, email, or call. Monnit’s hardwired thermocouples feature a needle-style probe at the end of a 6’ lead (a K-Type Quick Connect Thermocouple is also available).